Bumper Plates Or Technique Plates For Recovery Training?
-
- Registered User
- Posts: 87
- Joined: Tue Jan 17, 2023 2:49 pm
Bumper Plates Or Technique Plates For Recovery Training?
Please bear with me.
Just started training with free weights in the last few months. A bit over a week ago, working up to 90 lbs. of plates deadlifting, working with less weight to get my form perfected, first, I'd been elevating the bar to the standard height with stacks of old catalogs and magazines under the plates. One time, setting the bar down, the right side went rolling off the stack. Had to grab and stop it before it rolled off and damaged something nearby.
Pulled a back muscle. Pretty badly, because I'm still recovering from it.
When I'm ready to start lifting again I don't wish to chance repeating that. I was thinking maybe a set of either bumper plates or technique plates to get the bar to the correct DL height off the floor.
Problem is: From what I"m reading: None of those products seem robust enough to handle a 45 lb. Olympic bar plus additional regular plates so I can gradually work back up to regular 45 lb. Olympic plates on the bar. I"m thinking I'm going to want to start real light, like maybe only 20-30 lbs. (10-15 lbs./side) of plates, and work up to 70 lbs. (35 lbs./side) before moving up to the 45 lb. plates.
Suggestions?
Just started training with free weights in the last few months. A bit over a week ago, working up to 90 lbs. of plates deadlifting, working with less weight to get my form perfected, first, I'd been elevating the bar to the standard height with stacks of old catalogs and magazines under the plates. One time, setting the bar down, the right side went rolling off the stack. Had to grab and stop it before it rolled off and damaged something nearby.
Pulled a back muscle. Pretty badly, because I'm still recovering from it.
When I'm ready to start lifting again I don't wish to chance repeating that. I was thinking maybe a set of either bumper plates or technique plates to get the bar to the correct DL height off the floor.
Problem is: From what I"m reading: None of those products seem robust enough to handle a 45 lb. Olympic bar plus additional regular plates so I can gradually work back up to regular 45 lb. Olympic plates on the bar. I"m thinking I'm going to want to start real light, like maybe only 20-30 lbs. (10-15 lbs./side) of plates, and work up to 70 lbs. (35 lbs./side) before moving up to the 45 lb. plates.
Suggestions?
-
- Registered User
- Posts: 1298
- Joined: Wed Jun 05, 2019 5:26 am
Re: Bumper Plates Or Technique Plates For Recovery Training?
Are you in a home gym or an actual gym?
I think rogue and some others sell 10-35 lbs bumbers that can take deadlifts by themselves as long as you don't drop them from lock out.
You could try RDLs out of a rack instead of the floor. Unrack the bar touch it to the floor/spacer every rep and rerack it at the end of the set. You could also just pull it off the floor as a first rep deficit.
Get a horse stall mat and cut it up into squares. Cut four thin strips and attach them to two of the squares as stoppers. Stack them up to the height you want with the stripped ones on top. This would work with plywood too.
Rack pulls from pins at the height you want you're not going to mess up the bar with less than 135.
I think rogue and some others sell 10-35 lbs bumbers that can take deadlifts by themselves as long as you don't drop them from lock out.
You could try RDLs out of a rack instead of the floor. Unrack the bar touch it to the floor/spacer every rep and rerack it at the end of the set. You could also just pull it off the floor as a first rep deficit.
Get a horse stall mat and cut it up into squares. Cut four thin strips and attach them to two of the squares as stoppers. Stack them up to the height you want with the stripped ones on top. This would work with plywood too.
Rack pulls from pins at the height you want you're not going to mess up the bar with less than 135.
- Hardartery
- Registered User
- Posts: 3137
- Joined: Sat Nov 21, 2020 6:28 pm
- Location: Fat City
Re: Bumper Plates Or Technique Plates For Recovery Training?
First, you should never drop a bar in training intentionally, especially as a someone starting out. You should absolutely be in total control of the eccentric at all times, it's going to do more for your development than the concentric and help you avoid injury. I know that it's big on the social media platforms to drop stuff and act all cranked up. That's stupid, and happening for clicks not for anything else. That said, training plates are perfectly capable of handling being set down, as are even the cheaper low weight bumpers. Either way, you are fine. Just don't act like a moron dropping stuff from lockout.
It doesn't hurt to cut up a 4 x 4 post and nail a 2 x 4 across each end of a row of them and make a sturdy little block that the weights can't roll off of. They don't have to look like crap, weightlifting halls ahve made blosck like that for decades before places like Rogue and Eleiko started selling the fancy version.
It doesn't hurt to cut up a 4 x 4 post and nail a 2 x 4 across each end of a row of them and make a sturdy little block that the weights can't roll off of. They don't have to look like crap, weightlifting halls ahve made blosck like that for decades before places like Rogue and Eleiko started selling the fancy version.
- Allentown
- Likes Beer
- Posts: 10019
- Joined: Fri Sep 15, 2017 8:41 am
- Location: Grindville, West MI. Pop: 2 Gainzgoblins
- Age: 40
Re: Bumper Plates Or Technique Plates For Recovery Training?
A set of 25lb bumpers would be a good purchase that you'll use for lots of things. Weights below that just RDL, or start the first rep from the floor then RDL/lower to approximately the right height. The height isn't that important.
- augeleven
- Registered User
- Posts: 4463
- Joined: Thu Sep 28, 2017 1:47 pm
- Location: 9th level
- Age: 43
Re: Bumper Plates Or Technique Plates For Recovery Training?
When I started stronglifts I started deadlifting with just bar and some wood rounds I got at Home Depot.
https://www.homedepot.com/p/Edge-Glued- ... /204510767
I used them for a bit, but they mostly just sit around now. Sometimes I use them for standing on for deficits. But at ~$30 for a pair (provided you already have a 2” hole saw bit…). It’s a lot cheaper than bumper or technique plates.
https://www.homedepot.com/p/Edge-Glued- ... /204510767
I used them for a bit, but they mostly just sit around now. Sometimes I use them for standing on for deficits. But at ~$30 for a pair (provided you already have a 2” hole saw bit…). It’s a lot cheaper than bumper or technique plates.
- Clearwater47
- Registered User
- Posts: 383
- Joined: Tue Jan 17, 2023 12:59 pm
- Location: Minnesota, USA
- Age: 49
Re: Bumper Plates Or Technique Plates For Recovery Training?
The round boards is something I never thought of before. Cool idea.
Bumper plates can absolutely work just fine. I have 10 pound bumpers and at one point had my son deadlifting with just those on the bar. Just need to be smart. As mentioned already, don't drop the bar. That's really about it. Also, take the plates off when you're done otherwise they will bend if you just let them sit like that for several hours, but the time it takes to do your deadlifts won't cause any issues at all.
Bumper plates can absolutely work just fine. I have 10 pound bumpers and at one point had my son deadlifting with just those on the bar. Just need to be smart. As mentioned already, don't drop the bar. That's really about it. Also, take the plates off when you're done otherwise they will bend if you just let them sit like that for several hours, but the time it takes to do your deadlifts won't cause any issues at all.
-
- Registered User
- Posts: 87
- Joined: Tue Jan 17, 2023 2:49 pm
Re: Bumper Plates Or Technique Plates For Recovery Training?
Home gym. With very limited space right now. (I'm correcting that.)
Vulcan has some economical black bumper plates they claim can be dropped, with the bar alone, from lockout and take it. They even have an attached video showing one attached to a torture-test machine dropping a plate from a good deal higher than that, repeatedly.
Unfortunately, no rack yet. Need to make room for it. But, yeah, I planned to re-start with RDLs, anyway.
Good idea, save for two problems: Space is so tight I've nowhere to put them out-of-the-way when they're not in-use and, the last time I bought horse stall mats they stank to high heaven.
I wasn't then and hadn't intended to going forward.Hardartery wrote: ↑Thu Feb 02, 2023 9:42 pm First, you should never drop a bar in training intentionally, especially as a someone starting out.
The problem occurred on the last rep, when I was getting tired, and didn't control the bar quite as well on the eccentric.
So you feel quality bumper plates or tech plates will handle being set down, maybe even a bit "firmly," with another 50-60 lbs. on the bar, as long as I don't literally drop the bar?Hardartery wrote: ↑Thu Feb 02, 2023 9:42 pm That said, training plates are perfectly capable of handling being set down, as are even the cheaper low weight bumpers. Either way, you are fine. Just don't act like a moron dropping stuff from lockout.
That had occurred to me, too. Same problem as the horse mats: Literally no place to get 'em out of the way when not in-use--the space I have now is that cramped.
Yeah, I figured probably 25 lbs. if I went with bumper plates. 10 lb. bumper plates don't appear very substantial and 15 lb. are probably marginal.
Hmmm... Might be an idea.
Thanks for the comments and suggestions, everybody!
I have a bit of time to figure this out. The back is getting a bit better day-by-day, but, I imagine it's going to be another couple weeks before I'll be ready.
- Hardartery
- Registered User
- Posts: 3137
- Joined: Sat Nov 21, 2020 6:28 pm
- Location: Fat City
Re: Bumper Plates Or Technique Plates For Recovery Training?
In my experience, even cheap bumpers were fine for a fair amount of abuse. We had a single set of 25's that my training partner liked to use when we did overhead. On a log, Axle, whatever we were doing, dropping from full extension (He is 6'-7, I am 6'-0) with 300 lbs or so total on the implement being used. We dropped as much as 360 or so from shoulder height with those 25's at the end of the implement taking the beating. Eventually the metal center rings got a little loose in the plates. You will not abuse yours the way we did, my partner in particular (He didn't like doing eccentrics). My wife did deads with a standard bar and plywood disks on it for height (Like what @augeleven suggested but I just cut up a piece of leftover plywood I had) and she failed to destroy them even with little change plates added until she got up to a full plate.Michiganian wrote: ↑Fri Feb 03, 2023 8:22 am
I wasn't then and hadn't intended to going forward.Hardartery wrote: ↑Thu Feb 02, 2023 9:42 pm First, you should never drop a bar in training intentionally, especially as a someone starting out.
The problem occurred on the last rep, when I was getting tired, and didn't control the bar quite as well on the eccentric.
So you feel quality bumper plates or tech plates will handle being set down, maybe even a bit "firmly," with another 50-60 lbs. on the bar, as long as I don't literally drop the bar?Hardartery wrote: ↑Thu Feb 02, 2023 9:42 pm That said, training plates are perfectly capable of handling being set down, as are even the cheaper low weight bumpers. Either way, you are fine. Just don't act like a moron dropping stuff from lockout.
That had occurred to me, too. Same problem as the horse mats: Literally no place to get 'em out of the way when not in-use--the space I have now is that cramped.
Hmmm... Might be an idea.
Thanks for the comments and suggestions, everybody!
I have a bit of time to figure this out. The back is getting a bit better day-by-day, but, I imagine it's going to be another couple weeks before I'll be ready.
Are you the guy that appears to be lifting in a living room or something in his training log? Definitely go bumpers if you are in a finished living space.
-
- Registered User
- Posts: 87
- Joined: Tue Jan 17, 2023 2:49 pm
Re: Bumper Plates Or Technique Plates For Recovery Training?
That's good to know. And, no, I won't be abusing mine quite that badlyHardartery wrote: ↑Fri Feb 03, 2023 10:08 am In my experience, even cheap bumpers were fine for a fair amount of abuse. ... You will not abuse yours the way we did, ...
![Image](https://www.LinxNet.com/misc/smilies/lol.gif)
No, I'm working out in our basement. Concrete floor with old school thin rubber-backed carpet tiles. I'm using Rep's rubber-coated grip plates.Hardartery wrote: ↑Fri Feb 03, 2023 10:08 am Are you the guy that appears to be lifting in a living room or something in his training log? Definitely go bumpers if you are in a finished living space.
I'm eventually going to acquire a set of Rubber Deadlift Mats because I figure even those rubber-coated plates would otherwise eventually destroy the carpet tiles after enough reps.
- Hardartery
- Registered User
- Posts: 3137
- Joined: Sat Nov 21, 2020 6:28 pm
- Location: Fat City
Re: Bumper Plates Or Technique Plates For Recovery Training?
I'll be honest, the biggest reason for rubber mats IMO is that it save the plates getting beat up. I know that's not why people buy them, but that's really what the mats accomplish in addition to noise reduction.Michiganian wrote: ↑Fri Feb 03, 2023 10:26 amThat's good to know. And, no, I won't be abusing mine quite that badlyHardartery wrote: ↑Fri Feb 03, 2023 10:08 am In my experience, even cheap bumpers were fine for a fair amount of abuse. ... You will not abuse yours the way we did, ...
No, I'm working out in our basement. Concrete floor with old school thin rubber-backed carpet tiles. I'm using Rep's rubber-coated grip plates.Hardartery wrote: ↑Fri Feb 03, 2023 10:08 am Are you the guy that appears to be lifting in a living room or something in his training log? Definitely go bumpers if you are in a finished living space.
I'm eventually going to acquire a set of Rubber Deadlift Mats because I figure even those rubber-coated plates would otherwise eventually destroy the carpet tiles after enough reps.
-
- Registered User
- Posts: 87
- Joined: Tue Jan 17, 2023 2:49 pm
Re: Bumper Plates Or Technique Plates For Recovery Training?
I know that's why most people buy them. But, in my case, I expect plates repeatedly landing on the same spots on thin, rubber-backed carpet tiles over concrete would be bound to eventually damage the carpet tiles. And they're so old there's no way I'd ever find replacements.Hardartery wrote: ↑Fri Feb 03, 2023 10:30 am I'll be honest, the biggest reason for rubber mats IMO is that it save the plates getting beat up. I know that's not why people buy them, but that's really what the mats accomplish in addition to noise reduction.
-
- Registered User
- Posts: 87
- Joined: Tue Jan 17, 2023 2:49 pm
Re: Bumper Plates Or Technique Plates For Recovery Training?
Update
After doing a lot of research, followed by a lengthy email exchange with Vulcan Strength, I ordered a pair of Vulcan Black 10 lb. bumper plates. They assured me those bumper plates would hold up to what I wanted to do.
After doing a lot of research, followed by a lengthy email exchange with Vulcan Strength, I ordered a pair of Vulcan Black 10 lb. bumper plates. They assured me those bumper plates would hold up to what I wanted to do.
-
- Registered User
- Posts: 87
- Joined: Tue Jan 17, 2023 2:49 pm
Re: Bumper Plates Or Technique Plates For Recovery Training?
Plates received ![Smile :)](./images/smilies/icon_e_smile.gif)
![Image](https://www.linxnet.com/misc/images/Fitness/Vulcan_10lb_Bumper_Plates-18pct.JPG)
Back is still a bit questionable, but, I'm going to try some RDLs with just the bar and those plates later today.
![Smile :)](./images/smilies/icon_e_smile.gif)
Back is still a bit questionable, but, I'm going to try some RDLs with just the bar and those plates later today.
-
- Registered User
- Posts: 87
- Joined: Tue Jan 17, 2023 2:49 pm
Re: Bumper Plates Or Technique Plates For Recovery Training?
Here we are, a month later, and I figured I'd post an update.
Vulcan's 10 lb. bumper plates have been everything Vulcan promised me they'd be. I've had up to 35 lbs./side of rubber-coated plates on the bar with them, doing RDLs. After the last rep I've been more-or-less dropping the bar from about mid-shin height. The Vulcan bumper plates have handled that just fine.
Vulcan's 10 lb. bumper plates have been everything Vulcan promised me they'd be. I've had up to 35 lbs./side of rubber-coated plates on the bar with them, doing RDLs. After the last rep I've been more-or-less dropping the bar from about mid-shin height. The Vulcan bumper plates have handled that just fine.